| Error Code | Message | Meanings | Field replaceable unit or action |
|---|---|---|---|
|
0175 |
Bad CRC1, stop POST task | EEPROM CRC1 is not correct (block number 6). | System board |
| 0176 | System Security. The system has been tampered with. | Security Chip was removed and attached again. |
|
|
0187 |
EAIA data access error | EEPROM access (read or write) failed. | System board |
|
0188 |
Invalid RFID Serialization Information Area or Bad CRC2 | EEPROM checksum is not correct (block number 0,1). EEPROM CRC2 is not correct (block number 6). | System board Box serial number needs to be reinstalled. |
|
0189 |
Invalid RFID Configuration Information Area | EEPROM checksum is not correct (block number 4,5). | System board UUID needs to be reinstalled. |
|
0190 |
Critical low-battery error | Critical Low Battery. | Charge the battery pack |
|
0191 |
System Security. Invalid remote change requested. | Bad system configuration change request detected. |
|
|
0192 |
System Security. Embedded Security hardware tamper detected. | Security chip ID matching failed. | System board |
|
0193 |
RF antenna has been removed | RFID antenna has been removed,which was once installed. | RFID model only |
|
0194 |
The computer is carried through a security gate | The computer is carried through a security gate (portal gate). | RFID model only |
|
0197 |
Invalid Remote Change Requested | Reported when the CRC of request packet in EEPROM Block #7 is wrong. | Recovery-Users need to send the system back to the service centers. |
| 0199 | System Security- Security password retry count exceeded | System administrator password retry expired (if failed 3 times) |
|
|
0200 |
Failure Fixed Disk | Fixed disk is not working or not configured properly. | Check to see if fixed disk is attached properly. Run setup. Find out if the fixed-disk type is correctly identified. |
|
0210 |
Stuck key | Stuck key on keyboard. | Run interactive tests of the keyboard and the auxiliary input devices. |
|
0211 |
Keyboard error | Keyboard not working | Run interactive tests of the keyboard and the auxiliary input devices. |
|
0212 |
Keyboard Controller Failed | Keyboard controller failed test. May require replacing the keyboard controller. | Run interactive tests of the keyboard and the auxiliary input devices. |
|
0213 |
Keyboard locked. Unlock key switch. | Unlock the system to proceed. | Run interactive tests of the keyboard and the auxiliary input devices. |
|
0220 |
Monitor type does not match CMOS. Run SETUP | Monitor type not correctly identified in Setup. | Load Setup Defaults in the BIOS Setup Utility. |
|
0230 |
Shadow RAM failed at offset nnnn | Shadow RAM failed at offset nnnn of the 64k block in which the error was detected. | System Board |
|
0231 |
System RAM failed at offset nnnn | System RAM failed at offset nnnn of in the 64k block in which the error was detected. |
|
|
0232 |
Extended RAM Failed at offset nnnn | Extended memory not working or not configured properly at offset nnnn. |
|
|
0250 |
System battery is dead. Replace and run SETUP | The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup to reconfigure the system | Replace the backup battery and run the BIOS Setup Utility to reset the time and date. |
|
0251 |
System CMOS checksum bad - default configuration | System CMOS has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in CMOS. The BIOS installed Default Setup Values. If you do not want these values, enter Setup and enter your own values. If the error persists, check the system battery or contact your dealer. | Replace the backup battery and run the BIOS Setup Utility to reset the time and date. |
| 0260 | System timer error | The timer test failed. Requires repair of system board. |
|
|
0270 |
Real time clock error | Real-time Clock fails BIOS hardware test. May require board repair. |
|
|
0271 |
Check date and time settings | BIOS found date or time out of range and reset the Real-time Clock. May require setting legal date (1991–2099). | Run the BIOS Setup Utility to reset the time and date. |
|
0280 |
Previous boot incomplete - Default configuration used | Previous POST did not complete successfully. POST loads default values and offers to run Setup. If the failure was caused by incorrect values and they are not corrected, the next boot will likely fail. On system with control of wait states, improper Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify that wait-state configuration is correct. This error is cleared the next time the system is booted. | Customized not to display this message. |
|
0281 |
Memory Size found by POST different from CMOS | Memory size found by POST different from CMOS. | Load Setup Default in the BIOS Setup Utility. |
| 02B0 | Diskette drive A error Diskette drive B error | Drive A or B is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the proper diskette type in Setup and that the diskette drive is attached correctly. | Load Setup Default in the BIOS Setup Utility. |
| 02B2 | Incorrect Drive A type - run SETUP | Type of floppy drive A not correctly identified in Setup | Diskette Drive |
| 02B3 | Incorrect Drive B type - run SETUP | Type of floppy drive B not correctly identified in Setup | Diskette Drive |
| 02D0 | System cache error- Cache disabled | RAM cache failed and BIOS disabled the cache. On older boards, check the cache jumpers. You may have to replace that cache. See your dealer. A disabled-cache slows system performance considerably. | System Board |
| 02F0 | CPU ID | CPU socket number for Multiprocessor error. | |
| 02F4 | EISA CMOS not writable | Server BIOS 2 test error Cannot write to EISA CMOS. |
|
| 02F5 | DMA Test Failed | Server BIOS 2 test error Cannot write to extended DMA (Direct Memory Access) registers. |
|
| 02F6 | Software NMI Failed | Server BIOS 2 test error Cannot generate software NMI (Non-Maskable Interrupt). |
|
| 02F7 | Fail-safe Timer NMI Failed | Server BIOS 2 test error Fail-safe Timer takers too long. |
|
|
1801 |
Unsupported docking station is attached. | Attached docking station is not supported by the product. | Power off and remove the docking station |
进入上海新宇笔记本维修主力站点 |
|
免费服务电话：800 820 9120 |
笔 |
| 我们的地址：上海市南丹东路228弄3号楼402室 | |
| 我们的电话：021-64283052 64283432 | |
| 我们的传真：021－54254762 | |
| E-mail:13918440336@sohu.com | |
| 24小时报修热线：13391203680 赵先生(维修工程师) | |
最拿手维修： 松下，NEC，TCL，宏基，三星，LG，清华紫光 笔记本液晶屏维修，笔记本主板维修，笔记本电池维修... |
|
>>与我们客户服务取得联系<<< |
|
2005-2006 上海新宇笔记本维修中心公司地址:上海市南丹东路228弄3号楼402室
我们的电话：021-64283052 64283432 ; 我们的传真：021－54254762 E-mail:13918440336@sohu.com