Error code
Symptom or error
FRU or action, in sequence
0175 Bad CRC1, stop POST task. The EEPROM checksum is not correct. System board.
0187 EAIA data access error. The access to EEPROM has failed. System board.
0188 Invalid RFID serialization information area or bad CRC2. The EEPROM checksum is not correct. System board.
0189 Invalid RFID configuration information area. The EEPROM checksum is not correct. System board
0190 Critical low battery error.
  1. Charge the battery pack
  2. Battery pack
0193 RF antenna has been removed. Enter the supervisor password
0194 The computer has been carried through a security gate. Enter the supervisor password
0195 Security hardware tamper detected
  1. Enter BIOS Setup Utility by entering the supervisor password, and select Config, select Security Chip, then click Clear Security Chip to clear this error
  2. Security Chip
  3. System board
0196 Security hardware removed
  • Enter BIOS Setup Utility by entering the supervisor password, and select Config, select Security Chip, then click Clear Security Chip to clear this error
  • Security Chip
  • System board
0197 Invalid Remote change requested. The remote configuration for the security chip has failed. Confirm the operation and try again.
01C9 More than one Ethernet devices are found. Remove one of them and press the Esc key to continue.
  1. Remove either a Mini PCI Ethernet card or an Ethernet daughter card, other wise press the Esc key to ignore the warning message.
  2. System board
0200 Hard disk drive error. The hard disk drive is not working.
  1. Reseat the hard disk drive.
  2. Load Setup Defaults in BIOS Setup Utility.
  3. Hard disk drive.
  4. System board
021x Stuck key Keyboard error Run an interactive tests of the keyboard and the auxiliary input device.
0220 Monitor type error. Monitor type does not match the one specified in CMOS. Load Setup Defaults in BIOS Setup Utility.
0230 Shadow RAM error. The shadow RAM failure at offset nnnn. System board.
0231 System RAM error. System RAM failure at offset nnnn.
  1. DIMM.
  2. System board.
0232 Extended RAM error. Extended RAM failure at offset nnnn.
  1. DIMM.
  2. System board.
0250 System battery error. System battery is dead Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0251 System CMOS checksum bad. Default configuration used Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0252 Password checksum bad. The password is cleared. Reset the password by running BIOS Setup Utility.
0260 System timer error
  1. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
  2. System board.
0270 Real time clock error
  1. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
  2. System board.
0271 Date and time error. Neither the date nor the time is set in the computer. Run BIOS Setup Utility to reset the time and date.
0280 Boot incomplete error. Default configuration used
  1. Load Setup Defaults in BIOS Setup Utility.
  2. DIMM.
  3. System board.
02B2 Incorrect drive A type.
  1. Diskette drive.
    　
  2. External FDD cable.
    　
  3. I/O card
02F4 EISA CMOS not writable.
  1. Load Setup Defaults in BIOS Setup Utility.
  2. Replace the backup battery.
  3. System board.
02F5 DIMM test failure
  1. DIMM.
  2. System board.
02F6 Software NMI failure
  1. DIMM.
  2. System board.
02F7 Fail-safe timer NMI failure
  1. DIMM.
  2. System board.

进入上海新宇笔记本维修主力站点

免费服务电话：800 820 9120

笔
记
本
维
修
找
新
宇

新
宇
做
的
是
信
誉
我们的地址：上海市南丹东路228弄3号楼402室
我们的电话：021-64283052 64283432
我们的传真：021－54254762
E-mail:13918440336@sohu.com
24小时报修热线：13391203680 赵先生(维修工程师)

最拿手维修：

IBM，DELL，SONY，华硕，东芝，联想，惠普，富士，苹果

松下，NEC，TCL，宏基，三星，LG，清华紫光

笔记本液晶屏维修，笔记本主板维修，笔记本电池维修...

>>与我们客户服务取得联系<<<

 

返回首页 网站地图

2005-2006 上海新宇笔记本维修中心公司地址:上海市南丹东路228弄3号楼402室
我们的电话：021-64283052 64283432 ; 我们的传真：021－54254762 E-mail:13918440336@sohu.com